YJ-30 Hydraulic shearing machine
Shear diameter（kn）：50mm
power：7.5kw
Principle：Mainly used for cutting and sawing of metal materials and various alloy materials
Application：Cutting brass rods/tubes
Updraft Machine
Density:8.9kg/dm3
Tensile strength:>170N/mm2
Elongation:>35%
Electrical conductivity:no less than 100%IACS (2mm dia soft wire)
Principle：The up drawing oxygen free copper rod continuous casting unit is a new technology to produce large length bright oxygen free rods, pipes, flat billets and other profiles
Application：Application：1. Copper pole: used for cable, electric wire, electromagnetic wire, enamelled wire, telephone wire, computer wire, etc.2. Copper pipe: copper material used for air conditioner, household industry copper pipe, joint, etc.3. Flat billet: used as the billet of copper busbar, electrical components, rolled copper strip, etc.4. Copper alloy wire: It is used as the blank of bearings, copper shafts, copper sleeves, welding wires, electronic decoration and other products for automobiles, high-speed trams, and mechanical products.
Small metal smelting furnace
Input voltage: 380V±10% three-phase, 50/60Hz
Maximum input power: 45KW
Power cooling requirement: ≥0.2Mpa≥4L/min
Output frequency: 1-20KHz
Cooling water requirements for the entire system: ≥0.2Mpa ≥10L/min
Maximum input current: 68A
Cupola furnace
Melting Rate： copper：300kg/h brass：400kg/h
Power： 75kw
Principle：The metal is heated and melted by the huge induced current in the melting channel as the secondary of the transformer. Due to the action of electromagnetic force, the liquid metal is forced to move along the melting channel, so that the whole metal is continuously heated.
Application：
1. Protect the bottom of the furnace
2. Gather molten iron and slag into the forehearth
3. The hearth without a forehearth is mainly used to store molten iron.
PLC-Straightening and cutting machine
Wire diameter range: 8.0-16mm
Straightening accuracy: 0.1mm/m
Cutting length: minimum 200mm, length can be adjusted at will
Straightening speed: 10-30m/min
Power requirements: 380V/50HZ
Host power: 15KW
Machine size: 3200×740×1400mm
Principle：The motor drives the belt drive and can rotate the straightening cylinder at high speed to straighten the steel bars passing through the straightening cylinder and remove the rust on the surface of the steel bars; The electric motor can drive two conveying and pressing rollers through another pair of decelerating belt drives and gear reduction boxes, which can lead the steel bar to move forward. On the other hand, it can drive the crank wheel, which can promote the hammer head to move up and down. When the reinforcement is adjusted to a predetermined length, the hammer head will hammer on the knife rest to cut the reinforcement. When the cut reinforcement falls into the receiving frame, it will be subjected to the elastic force of the spring, and the knife rest will return to its original position, completing a work cycle.
Application：Straightening and cutting machines have the characteristics of fast speed, small error, no wire running, reasonable structure, convenient operation, safety and reliability, and can be widely used in various fields of hardware products and handicraft production.
Valve Automatic Production Line
Maximum processing size：6000*200
Punching processing range：5-25
Maximum mold that can be installed：16 punches, 1 cut, 1 embossing
Clamping method：Pneumatic mechanical clamp
Application：Scope of application. Various steel, iron, copper, aluminum plates, formed steelScope of application. Various steel, iron, copper, aluminum plates, formed steel
Busbar punching and bending machine
Maximum processing size：6000*200
Punching processing range：5-25
Maximum mold that can be installed：16 punches, 1 cut, 1 embossing
Clamping method：Pneumatic mechanical clamp
Application：Scope of application. Various steel, iron, copper, aluminum plates, formed steelScope of application. Various steel, iron, copper, aluminum plates, formed steel
GYT-120 Melting Furnace
Model：GYT-120-melting furnace
Melting Rate： copper：500kg/h brass：600kg/h
Power： 120kw
Principle：The metal is heated and melted by the huge induced current in the melting channel as the secondary of the transformer. Due to the action of electromagnetic force, the liquid metal is forced to move along the melting channel, so that the whole metal is continuously heated.
Application：Store brass solution, cast brass rod/tube
Material Opening Elevator Machine
Saw blade outer diameter：Φ70-270mm
Saw blade outer diameter：Φ16.22.27.32
main motor power：750w
Principle：
Application：Used for gear grinding of high speed steel and tungsten steel
LD-60 Vertical Multi-Roller Straightening Machine
Processing range：S160mm-425mm
Speed：40 m/min
Power：75*2kw
Principle：The bending part of the metal bar is subjected to a considerable reverse bending or tensile force, so that the bar produces a certain elastic-plastic deformation. When the external force is removed, the bar undergoes elastic recovery to achieve a straightening effect.
Application：This machine is suitable for straightening non-circular special-shaped materials such as hexagonal and square shapes.
Saw blade gear grinding machine
Saw blade outer diameter：Φ70-270mm
Saw blade outer diameter：Φ16.22.27.32
main motor power：750w
Principle：
Application：Used for gear grinding of high speed steel and tungsten steel
CM0516-PLC Double head chamfering machine
model：CM0516
Applicable rod diameter (mm)：2000-4000
power：14kw
weight：1150kg
Principle：The automatic chamfering machine pulls the two ends of the distributor into the alignment roller table one by one, and the alignment roller table aligns the two ends to the chamfer end. The double end chamfering machine slides along the inclined track and enters the friction wheel of the main drive through the alignment positioning plate. The pressing device lifts to press the workpiece, starts the main drive shaft to rotate the workpiece, and sends it to the grinder to start the double chamfering
Application：This equipment uses a power turning head to cut the end face of the bar head chamferingor end fush for subsequent processing by automatic lathes or centerless grinders. lt is aprocessing tool for the material used in bars and automatic lathes to speed up production
efficiency.
Fully Automatic Bar Cutting Machine
Cutting diameter：Φ8-45mm
Maximum cutting length：120mm
Working frequency：10-100pice/min
Principle：
Application：Used for cutting round, triangular, square, flat, hexagonal, pipe and special-shaped materials
Hydraulic alligator shear scrap metal shearing machine
Processing range：S10-40mm
Speed：35 m/min
Power：5.5KW*2,400W*13
Principle：The bending part of the metal bar is subjected to a considerable reverse bending or tensile force, so that the bar produces a certain elastic-plastic deformation. When the external force is removed, the bar undergoes elastic recovery to achieve a straightening effect.
Application：This machine is suitable for straightening non-circular special-shaped materials such as hexagonal and square shapes.